PCSTATS     
[X]   Directory of
Guides & Reviews

Beginners Guides
Motherboards by Brand
Weekly Newsletter
Archived Newsletters

+70 MORE Beginner GUIDES....
Elan Vital T10 Case Review
Elan Vital T10 Case Review - PCSTATS
With the T10, Elan Vital has managed to assemble what has to be one of the world's worst cases we've ever seen.
 62% Rating:   
Filed under: Cases Published:  Author: 
External Mfg. Website: Elan Vital May 21 2001   Max Page  
Home > Reviews > Cases > Elan Vital T10

Elan Vital T10 Case Review

With the T10, Elan Vital has managed to assemble what has to be one of the worst cases we've ever used. The odd thing is, on the inside of this horrible case they've included some very cool features.... That's of little comfort however, considering how badly the case has been designed on the outside. H'mm... a case that works well on the inside but is impossible to use. Great - just what we all need!

In all fairness we tried to give this case the benefit of the doubt, but after using it for some time now it has only managed to get itself chucked into a corner of the storage room - next to the old 486 AT case. The 486 AT case, I might add, has been seeing more use as a print server lately.

Why do we think the T10 is such a badly designed case? Well it has nothing to do with materials, or anything along the lines of razor-sharp corners, but rather the bezel and the design of the frame. Those two areas represent the key components of any case design, and any deficiencies shine through more than glaringly.

Make sure you remember this bezel as one case you should NEVER buy.

The case come with 3X 5.25" bays, 1X 3.5" FDD bay and 3X 3.5" HDD bays. An 80mm intake fan and 80mm exhaust port round out the cooling features. Power comes from a generic 250 Watt ATX power supply.

The reset switch is only accessible with a paperclip or pen, and the power switch is next to impossible to use.

Cooling on the T10 is of the usual flair. Air vents are positioned at the top of the case directly above the powersupply to allow hot air to naturally escape, and an intake and exhaust fan are positioned at two locations to help with air pressure. Both the intake and the exhaust fan areas are 80mm in size, but only one fan is included with the case. The venting on the bezel is almost non-existant, rendering the effectiveness of the intake fan quite questionable.

While the sheet metal used in the construction of the T10 is of good quality, the case is a veritable jig-saw puzzle waiting to happen. As such, it is difficult to get into easily.

To open this case there are several steps. The first is to unscrew a locking mechanism on the rear of the case, where if necessary a lock can be placed.

Once the locking screw is released the side of case slides back, and then up. To install a motherboard or get better access to the inside, a support bar must be removed. The bar just pops out of its position. With the top and other side panel removed it is easy to see why this case is so complicated. There is almost a double layer of metal over the entire case. Again it is not a question of quality of materials, but rather poor design, or for that matter over design.

© 2023 PCSTATS.com Next Page >

 

Contents of Article: Elan Vital T10
 Pg 1.  — Elan Vital T10 Case Review
 Pg 2.  More pain with the T10

 
Hardware Sections 


 
PCSTATS Network Features Information About Us Contact
FrostyTech
PCSTATS Newsletter
Tech Glossary
Technology WebSite Listings
News Archives
(Review RSS Feed)
Site Map
PCstats Wallpaper
About Us
Privacy Policy
Advertise on PCSTATS

How's Our Driving?
© Copyright 1999-2023 www.pcstats.com All rights reserved. Privacy policy and Terms of Use.